Various FLOATING SEAT

@ A type FLOATING SEAT (standard type) PAT.
A type
*A strong body is used and great importance
  is attached to practicability.
*FLOATING  SEAT have the  confidence  not
  only  in Japan  but also  throughout the 
  world and  5,000 sets  of FLOATING SEAT
  have been supplied.
*Regarding the durability,the products have
  been used for 10 years or more until now.
*The excellent  tightening  force and  the
  tightening  precision have  been already
  proved in the actual results of supply.

*Due to thread machining in the inner diameter,in some type,FLOATING SEAT
  serves also as a nut.
*One side pressure feed type with excellent workability (Utility Model) can
  be provided.
*In  some type, even if a  booster screw part is broken, it can be restored
  easily by exchanging parts.(Patent Pending)[option]
*Key way or thread machining can be applied to the inner diameter.
@ K type FLOATING SEAT (light-weight type) PAT.P
K type
*Light weight and high performance are com-
  bined at the high order.
*Its weight is 40% of the standard type.
*Although this type has  been  processed by
  special treatment of aluminum alloy(body)
  the  booster part necessitating  strength
  can  be reinforced  by its own  structure
  (Patent Pending) thereby the disadvantage
  in a  conventional type made of  aluminum
  can be compensated.
*One side pressure  feed  positon type with
  good  workability  (Utility Model) can be
  provided.
*In some type, even if the booster screw part is damaged,it can be restored
  by exchanging parts.(Patent Pending)[option]
*Key way or thread machining can be applied to the inner diameter.




@ S type FLOATING SEAT (separate type) PAT.
s type
*This  type is  dealt with  by  the careful
  design theory.
*Although  this  is a  separate  type, the
  pressure  feed work  can be  done at  one
  position.
*Even  at a  position  where the  clamping
  work is difficult, the strong  tightening
  force and the  high tightening  precision
  can be realized.
*Even when attaching or detaching is diff-
  icult with a usual nut, the  attaching or
  detaching can be easily done in the sepa-
  rate type.
*Key way or thread machining can done in the inner diameter.
  
  This can not be manufactured in the annualr disk type.
@ H type FLOATING SEAT (hinge type) PAT.
‚gŒ^
*A  desk theory has been applied actually.
  Individual design with high precision.
*It can  be set without detaching an ardor
  nut.
*Since it can  be set to the screw thight-
  ening  position  previously, the  racing
  work may be omitted.
  (with inner diameter threaded)
*Its tightening  precision is the  same as
  that of the standard type.
*Key  way or thread machining can  be done
  in the inner diameter.
  
  This can not be manufactured in the annualr disk type.
@DR type PRESSURE SEAT (annular disk type) PAT.P not a floating type
DR type
*Individual  design  in response to request
  of a simpler hydraulic nut.
*It is  a pressure seat taking great impor-
  tance  only  to the thightening function.
   (inferior to the  A  type or the like in
  the tightening force)
*Low cost is realized in single function.
*Key way or thread machining can be done in
  the inner diameter.



  (Remark) This type is not suitable in the case of  necessitating
  the precision.
  (Because of pushing at the annular disk surface)
@ ONE SIDE PRESSURE FEED POSITION TYPE (option)
@ ONE SIDE PRESSURE FEED POSITION TYPE

           Pressure feed positions are usually separat-
           ed to the right and to the left,  but in the
           case  of "one-side  pressure  feed  position
           type", since the pressure feed positions are
           ocated to one side,the pressure feed at both
           two positons  can  be done without  rotating
           the shaft.
                          (Utility Model)

           This type can be applied to
           A type, K type, DR tyupe in
           responce to your request.


Š”Žฎ‰๏Žะ@–F“cค‰๏